Extech CAT IV 1000A Clamp Meter + IR Thermometer
The Extech 1000A Clamp Meter + IR Thermometer conducts true RMS current and voltage measurements.
Features
- Built-in non-contact IR Thermometer with laser pointer
- Peak hold captures inrush currents and transients
- Includes 8-piece professional test lead set
- Free ground shipping
- Expedited repair and warranty service
- Lifetime technical support
- More
The Extech 1000A Clamp Meter + IR Thermometer is a full size true RMS multimeter that features a built-in non-contact IR thermometer with laser pointer. Multimeter functions included AC/DC voltage, resistance, capacitance, frequency, diode, and continuity. The 1.7" jaw opening fits conductors up to 750MCM or two 500MCM. Unit functions include peak hold to capture inrush currents and transients, data hold, min/max, auto power off, and an autoranging function with manual range button.
The meter comes with an 8-piece professional test lead set. The kti includes two 42" PVC lead extensions with shrouded banana plugs at both ends, two modular 4" heavy duty test probe handles with 0.16" banana plug tip, two standard size alligator clips with insulated rubber boot, and two extra large, double-insulated, alligator clips with sharp teeth for piercing insulated wires. The jaw opens to 0.8".
- AC current range: 0.1 to 1000A
- AC current basic accuracy: ±2.8%
- DC current range: 0.1 to 1000A
- DC current basic accuracy: ±2.8%
- AC voltage range: 0.1mV to 1000V
- AC voltage basic accuracy: ±1.5%
- DC voltage range: 0.1mV to 1000V
- DC voltage basic accuracy: ±2.8%
- Resistance range: 0.1 to 40MΩ
- Resistance basic accuracy: ±1.5%
- Capacitance range: 0.001nF to 40,000μF
- Capacitance basic accuracy: ±3.0%
- Frequency range: 0.001kHz to 4kHz
- Frequency basic accuracy: ±1.5%
- IR temperature range: -58 to 518ºF (-50 to 270ºC)
- IR temperature basic accuracy: ±2.0% rdg or ±4ºF/±2ºC
- Type K temperature range: -4 to 1400ºF (-20 to 760ºC)
- Type K temperature basic accuracy: ±(3%rdg+9°F/5ºC)
- Continuity: yes
- Inrush: yes
- Diode: yes
- Dimensions: 10.6x4.3x2" (270x110x50mm)
- Weight: 13.6oz (386g)
- (1) Meter
- (1) Type K probe
- (2) CAT IV standard test leads
- (2) 42" (1m) PVC lead extensions with shrouded banana plugs at both ends
- (2) Modular 4" (102mm) heavy duty test probe handles with 0.16" (4mm) banana plug tip
- (2) Standard size alligator clips with insulated rubber boot
- (2) Extra large, double-insulated, alligator clips with sharp teeth for piercing insulated wire
- (1) 9V battery
- (1) Belt holster
Select Options
In The News
Cal Poly, San Luis Obispo Manages Monitoring Efforts in Morro Bay
California Polytechnic State University, San Luis Obispo (Cal Poly, SLO), has been monitoring Morro Bay for decades, and while the monitoring program has changed over the years, the dedication to monitoring the bay has remained the same. The project started in 2006 as a Packard Foundation-funded initiative to monitor water quality flowing in and out of Morro Bay. The goal at the time was to use the data collected to develop and inform an ecosystem-based management plan in collaboration with the Morro Bay National Estuary Program (MBNEP). Since the estuary was the focus at the time, researchers were monitoring water flowing into the estuary from Chorro Creek and Los Osos Creek.
Read More
Green Water in Green Bay: Using Data Buoys to Monitor the Southern Bay
While the bay of Green Bay has been referred to as the largest freshwater “estuary” in the world, the watershed hosts intensive agriculture and contributes one-third of Lake Michigan’s total phosphorus load. The Fox River flows into the bay, carrying excess nutrients largely the result of non-point source runoff from the watershed. With a history of deterioration extending well into the last century, the bay ecosystem suffered significant declines in water quality. This, in turn, stimulated major clean-up and ongoing restoration efforts to improve water quality. Tracking these changes is an important aspect of ecosystem management.
Read More
Cross-Border Sewage Contaminated Flows: Monitoring the Tijuana River
The Tijuana River runs across the US-Mexico boundary, flowing into and throughout southern California, carrying with it nutrients and contaminants throughout the estuary. In recent decades, the flows have been heavily polluted with untreated sewage from the City of Tijuana. The wastewater enters the greater Tijuana River estuary, impacting coastal communities and disrupting the natural environment. In order to better understand these cross-border flows, researchers out of San Diego University sought to monitor the waterway test the capabilities of in-situ sensors to measure the contaminated water. Natalie Mladenov and Trent Biggs were two of the researchers involved in the project, deploying a real-time monitoring system in May of 2021.
Read More
